Brush indicator screen dirty. Do not use Hard Floor Cleaning Solution on carpet or upholstery. Avoid contact with eyes and skin. In case of contact with eyes, flush with cold water for 15 minutes. In case of contact with skin, wash with water. If Irritation persists, call a physician. Pour detergent into tank.
Fill tank to fill line B 1 gallon with hot tap water. If rubber ring C on cap has become dislodged, reposition it with uneven side against ledge D as shown. When the recovery tank is full, the automatic shut-off will engage see page 8 and the tank must be emptied. To prevent possible leaking, remove clean solution tank Fig. If cleaning stairs or upholstery, remove hose by reversing procedure as shown on page The lid replaces in a hinge-like manner. Position the front of lid under tabs.
G on front of tank. Rotate lid down onto tank. Make sure that the lid is secure on all sides before placing tank on cleaner. For full suction, it is important that the recovery tank lid is properly secured before cleaning. To continue cleaning stairs or upholstery, replace hose as shown on page Raise handle to upright position and replace upper clean solution tank. Vacuum thoroughly - For carpet, use a vacuum cleaner with an agitator for best results.
Vacuum upholstery with. Use a crevice tool to reach into tufts and folds. Do not use the. Do not clean fabric marked. If your upholstery does not have a code, seek professional assistance. Wet a white absorbent cloth with the solution. In a small, hidden area, gently rub the surface with the dampened cloth. Wait ten minutes and check for color removal or bleed with white paper towel or cloth.
If surface has more than one color, check all colors. When cleaning entire floor, move furniture out of area to be cleaned. For furniture too heavy to move, place aluminum foil or wax paper under legs. This will prevent wood finishes from staining carpet.
Pin up furniture skirts and draperies. If no color change is visible, spray Spot and Stain Spray Cleaner onto spots and traffic areas. Wait at least ten minutes. Do not saturate carpet or upholstery with Spot and Stain Spray Cleaner. No cleaning solution removes all stains from all carpets. Stain removal varies with the type of spill, time elapsed before removal, carpet material, and carpet type.
To prevent staining, use plastic or aluminum foil to protect wood or metal surfaces from possible water spray. Allow time for carpet or upholstery to dry completely between cleaning and rinsing.
To rinse, follow the same procedure for cleaning only using hot tap water with no detergent in the upper clean solution tank. Allow carpet or upholstery to dry. To help prevent matting and resoiling the carpet, keep children and pets away from surface until it is completely dry.
If it is necessary to walk on damp carpet, place towels or white cloths on the traffic areas. If furniture must be replaced before the carpet is dry, use plastic or aluminum foil pads under legs of furniture so metal slides or wood finishes will not stain the carpet. Empty tanks, rinse with clear water and let air dry. Rinse the solution tank cap and recovery tank lid and let air dry. Remove debris from recovery tank filter and rinse with clean water.
Note: If the filter must be removed for cleaning, it is easier to replace if the filter is wet. Vacuum thoroughly after carpet has completely dried. If lint or other debris becomes lodged in nozzle, do not attempt to remove nozzle cover. Pour one to two cups of clear water on a non-carpeted floor. Do not pour water onto a wood floor. Repeat as necessary until debris is flushed out of nozzle. Some models have a nozzle clean-out tool for removing debris or if a non-car- peted floor is not available.
To use the tool: Disconnect carpet cleaner from electrical outlet. Slide tool into nozzle and remove debris as shown. To clean the outside of the machine, wipe off dirt with a cloth dampened in warm water and mild detergent.
Do not use solvent or petroleum based products to clean the machine. Move speed selector to LO for gentle cleaning or Hl for normal cleaning. Dry hands and plug cord into a properly grounded outlet. To avoid walking on damp carpet, start at the end of the room farthest from the door or path to sink where tanks will be emptied and filled.
Step on handle release pedal and lower handle to operating position; turn carpet cleaner ON. Squeeze trigger to release cleaning solution and slowly push carpet cleaner forward equals one wet stroke. Continue to squeeze trigger and slowly pull carpet cleaner back toward you second wet stroke. Release trigger and slowly push carpet cleaner forward over area just sprayed with solution dry stroke. Then slowly pull carpet cleaner back toward you without squeezing trigger dry stroke.
Overlap strokes by 1 inch to help prevent streaking. For heavily soiled areas, repeat steps Avoid saturating carpet, as noted below.
Note: To avoid saturating carpet, do not use more than 4 wet strokes over one area. Always end with dry strokes. For best cleaning results and to aid in faster drying of carpet, end with more dry strokes. Continue using dry strokes until little water is visible passing through the recovery tank lid. For normal solution spray, release button and continue to squeeze solution trigger. Repeat with spray and suction. When picking up spills on bare floors, use only the floor nozzle with the bare floor attachment in place and speed selector in the OFF position this will help prevent spreading the spill.
Although no cleaning solution can completely remove all spots, they can be treated by following the instructions provided by the manufacturer of the carpet, upholstery, or bare floor surface being cleaned.
To prevent possible leaking, remove clean solution tank and recovery tank before positioning bare attachment. Refer to Fig. Set tank aside do not set tank on furniture. With handle in upright position, tilt cleaner back so that handle rests on the floor. With foam strip A located under the netting in position as shown, place attachment on front of nozzle B. Make sure arrow on end of attachment points in the direction as shown. Push attachment against nozzle while rotating attachment downward until both ends snap into place.
Return carpet cleaner to upright position. Lower handle and replace recovery tank. Dry hands and plug carpet cleaner into a properly grounded outlet. To release solution, press trigger. Slowly move carpet cleaner forward and backward over area to be cleaned. To pick up dirty solution, release trigger and slowly move carpet cleaner over area where solution has just been dispersed. Use both forward and reverse strokes.
Remove attachment from nozzle and rinse in clear water. Do not remove plastic screen or foam from attachment. Powered hand tool has rotating brushes for extra scrubbing action on small carpet areas, carpeted stairs and upholstery.
Utility nozzle not included with all models can be used for carpet and upholstery in vehicles. To prevent possible leaking, remove clean solution tank by pressing down on tank handle D and pulling forward; set tank aside do not set tank on furniture. Remove hose from storage rack. Step on handle release pedal E and lower carpet cleaner handle until it rests on the floor. Welcome to ManualMachine. We have sent a verification link to to complete your registration.
Log In Sign Up. Forgot password? One Filter in a pack. Hoover Part , Hoover BZ Filter - Genuine. Fits Hoover C, , Hoover Insight Final Filter Part : Genuine Hoover Filter Assembly. Part no , H This filter measures 3. Hoover Spectrum Exhaust Filter - Genuine Hoover Spectrum Exhaust Filter. This is the pre-motor or primary filter. Part Hoover 2-in-1 Stick Vac Filter. Hoover Tank Dirty Water Filter , , Hoover Allergen Final Filter 4 Filters.
Three layer final filter. Fits model No. U , Hoover bagless, and WindTunnel. Fits Models : U, U, Replaces , , , Hoover Secondary Filter for U Cyclonic.
Part no , H Replaces part Hoover , Stick Vac Filter. Hoover Nano Lite Primary Hoover Central Vacuum Filter Cartridge. Part , , CVF Hoover Fits Hoover: S, , S and S Part : Inlet Filter Assembly.
Hoover Part Hoover Vacuum Filter - Genuine. Allergen filtration cassette final filter. Measures 6" by 6" approximately. Each sandwiched filter layer is designed to trap different size spores, Hoover Filter for Broom - Genuine.
In Stock, 7 available. In Stock, 20 available. Please note shipping times may be longer than expected due to carrier delays.
Shopping Cart. Submit Search. Sign in Sign in with Password. Cart Shopping Cart 0 item s in your cart. Restore a saved shopping cart. Hoover Upright Vacuum Parts. Preferred Partners of. Continue Shopping Proceed to Checkout. Search within model. Page A. Add to Cart. Bag Door Gasket Page B. Page C. Popular Parts. Drive Belt.
Flat Belt. Screw-Self Tapping. Handle Release Pedal-Black. Agitator Pulley Seal. Actuator Arm Assembly. Vacuum Parts. Accessories for the Hoover U Ask a question. The on and off switch no longer works. Is there a replacement I can purchase?
Barb for model number U asked on
0コメント